Quality inspections and tests of Keepac candy packaging machine will be carried out by the QC team. It will be scrutinized for different aspects, including bending, impact, compression, hardness, aging, and abrasion resistance performance. 2.
The product is approved to be of high quality after the thorough test by the third party quality experts. 3.
Consistent quality and functions are the characteristics of this product. 4.
Thanks to its easy operation, it greatly reduces time waste and allows people to start their work and tasks at the fastest speed. 5.
By helping reduce the workload, this product can prevent employees from getting tired. This will finally contribute to the improvement of productivity.
Mini Doypack Features
◪ BAG LOADING
The Pouch magazine is adjustable for different sized bag.
The Bags can be loaded while the machine is in operation
◪ BAG DETECTION
Multiple bag detection switches are used at various points in the cycle to ensure correct bag placement and full bag opening. Should a reject bag be detected it is ejected from the machine and the process continues. Rejected bags can be inspected by the operator and re-used if good.
◪ BAG OPENING
Pouches are individually removed from the cartridge with a unique combination of vacuum and pneumatic actuators. They are rotated/ transfered to the fill area and opened.
◪ TRANSITION CHUTE
doubling as a timing bucket. product enters the transition chute while the bag is being opened below. Upon pouch detection the Chute/Funnel enters the bag and opens the gate. Product is dispensed immediately, without spillage and protecting the seal from contamination. Difficult product that easily bridges is dispensed into the pouch directly from the filler, through the "open-gate''
During filling, pouches are held in place with our “positive-hold” gripper system. This allows for heavy weights and shock loads without altering bag Position;
Digitally controlled ribbed or flat constant heat seal bars give an integral attractive seal. Pouches are sealed ''in place" eliminating wrinkles, folded corners and non aligned seals
◪ MACHINE CONTROLS
System controls are fully solid state. utilizing a commercial Programmable Logic Controller [PLC] and Pneumatic. Indicator lights signal all cycle processes for easy monitoring.
Standard: Stainless Steel 304 Frame
|Model||Bag Width||Bag Length|
|Duplex 200||100mm ~ 200 mm||100mm ~ 300 mm|
Pneumatics component Airtac from Taiwan;
|Omron PID Temperature Controller;|
|Delta 7 inches from Taiwan;||Piab Vacuum Generator From Sweden;|
Low Operating & Maintenance cost;
InterLock, CE Application;
Interlock & Safety Relay;
The zipper opener is installed horizontally;
It is separated from the infeed hopper.
It would be worked when the pouch
is picked up and being horizontal. Then, it would be opened the pouch Zipper. When the pouch zipper is opened, then, it would be presented to the filling position for the infeed hopper to do the filling.
So The infeed hopper is only moved up and down, not necessary to be moved left and right as the vertical style. So the filler and collection chute could be inserted into that infeed hopper when the filler is installed. It would be reduce the free falling height and
And more safety for the production.
Like the powder application, the Auger filler would be lowed into that infeed hopper to reduce the free falling height. It is good to control the dusty;
* It would be moved up and down to flap Pouch Bottom to settle and tight the product.
It is better than the flat plate.
* The product settle should be worked during the filling. Most of
the filling are center on middle of the pouch.
So the product would be built the ‘little mountain’.
It is better to have the convexity product as the pictures show.
When it is flapped the filled pouch bottom by up and down movement, The product would be spread around inside of the pouch.
*When it is set to be work for 1 time, it would be Heavy Weight Supporter
* If the weight is over than 1kg, it needs the Heavy weight supporter
When it is set to be worked for Multi Times on the Panel, it would be product settle;
* It would be flapped the bottom of the product to tight the product into the bag;
Keepac has expanded its business into oversea market. 2.
Keepac has established its own technology center to meet the needs of competitive industries. 3.
We strive to achieve a better global environment, fulfil our ethical and social responsibilities, and work hard to exceed the expectations of our customers and employees. We have recognized the importance of friendly action on the environment. Our efforts in reducing resource demand, promoting green procurement, and adopting water resource management have gained some achievements.